diff options
Diffstat (limited to 'makefile')
| -rw-r--r-- | makefile | 72 |
1 files changed, 46 insertions, 26 deletions
@@ -1,9 +1,9 @@ ############################################################################### # # -# Make file for installing Basser Lout Version 3.21 # +# Make file for installing Basser Lout Version 3.22 # # # # Jeffrey H. Kingston # -# 10 May 2000 # +# 3 June 2000 # # # # make prg2lout Compile a small auxiliary program called prg2lout # # make lout Compile the Lout source # @@ -28,11 +28,26 @@ # Lout binary is to run. At present OSUNIX and OSDOS work but OSMAC # # doesn't work. # # # -# OSUNIX Unix in all its flavours, including Linux. # -# OSDOS MS-DOS etc. ("rb" and "wb" file access modes where needed) # -# OSMAC Macintosh # +# OSUNIX Unix in all its flavours, including Linux. # +# OSDOS MS-DOS etc. ("rb" and "wb" file access modes where needed) # +# OSMAC Macintosh # # # -# (2) This may be the trickiest step of all. On some systems, for example # +# (2) If you want to install Lout with debugging on for some reason, for # +# example if a guru has asked you to do this in the course of tracking # +# down some problem with Lout, then set these two macros as follows: # +# # +# DEBUGGING = 1 # +# TRACING = -g # +# # +# Lout will run a bit slower and its binary will be a bit larger if # +# you do this. The normal, non-debugging values are # +# # +# DEBUGGING = 0 # +# TRACING = # +# # +# These should appear like this below. # +# # +# (3) This may be the trickiest step of all. On some systems, for example # # NT under Visual C++, Lout's use of the system ftell() call causes # # a problem. This problem typically manifests itself on the *second* # # pass over a large document such as the Lout User's Guide: a message # @@ -49,13 +64,13 @@ # Cygnus gnuwin32 gcc djgpp # # Mingw32 # # # -# (3) Set the USESTAT macro defined below to 1 if the system you are # +# (4) Set the USESTAT macro defined below to 1 if the system you are # # compiling onto has the stat() file status system call. If you are # # unsure, or know it doesn't, set USESTAT to 0. The stat() call, # # if used, will allow Lout to determine the time of last change # # of database index files and rebuild them automatically if required. # # # -# (4) Set the SAFEDFT macro defined below to 1 if you want safe execution # +# (5) Set the SAFEDFT macro defined below to 1 if you want safe execution # # (i.e. disabling calls to system()) to be the default behaviour. You # # can always specify safe or unsafe execution by means of the -S and # # -U options to lout when processing a document; SAFEDFT means that # @@ -63,7 +78,7 @@ # required when formatting computer programs, so if in doubt, do not # # change the value of SAFEDFT. # # # -# (5) Set the following four macros defined below to appropriate values: # +# (6) Set the following four macros defined below to appropriate values: # # # # BINDIR Directory where Lout's binary goes. This directory is # # assumed to exist. # @@ -78,7 +93,7 @@ # MANDIR Directory where the lout and prg2lout online manual entries # # (in nroff -man) go. This directory is assumed to exist. # # # -# (6) Set the following two macros defined below to appropriate values. # +# (7) Set the following two macros defined below to appropriate values. # # I strongly recommend CHARIN=1 and CHAROUT=0 for all sites (English # # and non-English language). This way we get a truly international # # standard in which everyone has access to accented characters, yet # @@ -113,7 +128,7 @@ # as \ddd escape sequences and which are printed as one-byte # # literal characters. # # # -# (7) Set macro USELOC to one of the following values, NOT TO A LOCALE. # +# (8) Set macro USELOC to one of the following values, NOT TO A LOCALE. # # # # 0 Lout's error messages will always appear in English, and no # # source code related to locales will be executed (although # @@ -139,16 +154,16 @@ # # # For error messages in other languages, consult ./locale/README. # # # -# (8) Set macro COLLATE to either 0 or 1. If you set it to 1, Lout will # +# (9) Set macro COLLATE to either 0 or 1. If you set it to 1, Lout will # # use the strcoll() routine by default when sorting alphabetically # # (e.g. when sorting indexes), otherwise Lout will sort by default # -# based on the ISO codes of the characters. This defaul setting may # +# based on the ISO codes of the characters. This default setting may # # be changed during individual runs of Lout by the -l and -L flags. # # # -# (9) Execute "make prg2lout". This will compile the prg2lout program, # +# (10) Execute "make prg2lout". This will compile the prg2lout program, # # leaving its binary in this directory. Other directories unchanged. # # # -# (10) If you want to be able to produce compressed PDF files, as opposed to # +# (11) If you want to be able to produce compressed PDF files, as opposed to # # uncompressed ones, you need to: # # # # (a) obtain the zlib compression library from # @@ -172,16 +187,16 @@ # If you don't want zlib support or cannot obtain it or cannot use it, # # leave the PDF_COMPRESSION, ZLIB, and ZLIBPATH variables as they are. # # # -# (11) Execute "make lout". This will compile the Lout source, leaving the # +# (12) Execute "make lout". This will compile the Lout source, leaving the # # binary in this directory. No changes are made in other directories. # # # -# (12) This makefile assumes that Lout is not installed on your system # +# (13) This makefile assumes that Lout is not installed on your system # # already. If you do have an earlier version of Lout installed, # # the simplest way to get rid of it is to type "make uninstall" now. # # Of course, this is assuming that the old version was installed in the # # same directories as where you are about to install the new version. # # # -# (13) Execute "make install". This will do the following things: # +# (14) Execute "make install". This will do the following things: # # # # (a) It will copy the lout and prg2lout binaries into $(BINDIR); # # # @@ -204,22 +219,22 @@ # It is good to build the various files during installation because # # later runs will not have write permission in the library directories. # # # -# (14) Execute "make installman". This installs the manual entries for lout # +# (15) Execute "make installman". This installs the manual entries for lout # # and prg2lout into directory $(MANDIR), which is assumed to exist. # # These entries are troff files; plain text versions are also available # # in directory ./man if you need them (install them yourself). # # # -# (15) Execute "make installdoc". This creates directory $(DOCDIR) and # +# (16) Execute "make installdoc". This creates directory $(DOCDIR) and # # copies the Lout documentation into it. # # # -# (16) If you want French error messages, execute "make installfr" now. # +# (17) If you want French error messages, execute "make installfr" now. # # If you want German error messages, execute "make installde" now. # # These commands compile the error messages files into packed forms # # using the gencat command, and store them in $(LIBDIR)/locale. # # # -# (17) Execute "make clean". This cleans up this directory. # +# (18) Execute "make clean". This cleans up this directory. # # # -# (18) If the usual size of a piece of paper at your site is not A4, you # +# (19) If the usual size of a piece of paper at your site is not A4, you # # might like to now change the default value of the @PageType option # # on line 59 of file $(LIBDIR)/include/dsf: # # # @@ -232,7 +247,7 @@ # rest. You can find the list of known page types, alternative to A4, # # in the User's Guide, and also at line 640 in $(LIBDIR)/include/dsf. # # # -# (19) If the usual language at your site is not English, you might like to # +# (20) If the usual language at your site is not English, you might like to # # now change the default value of the @InitialLanguage option on line # # 255 of file $(LIBDIR)/include/bsf. This will mean that by default # # the date and words like Chapter and July will appear in a different # @@ -255,6 +270,9 @@ DBFIX = 0 USESTAT = 1 SAFEDFT = 0 +DEBUGGING = 1 +TRACING = -g + BINDIR = /export/home/6monthspace/jeff/bin LIBDIR = /export/home/6monthspace/jeff/lout.lib DOCDIR = /export/home/6monthspace/jeff/lout.doc @@ -305,7 +323,8 @@ CFLAGS = -DOS_UNIX=$(OSUNIX) \ -DCHAR_OUT=$(CHAROUT) \ -DLOCALE_ON=$(USELOC) \ -DASSERT_ON=1 $(COPTS) \ - -DDEBUG_ON=1 -g \ + -DDEBUG_ON=$(DEBUGGING) \ + $(TRACING) \ -DPDF_COMPRESSION=$(PDF_COMPRESSION) \ $(ZLIBPATH) @@ -314,7 +333,8 @@ OBJS = z01.o z02.o z03.o z04.o z05.o z06.o z07.o z08.o \ z17.o z18.o z19.o z20.o z21.o z22.o z23.o z24.o \ z25.o z26.o z27.o z28.o z29.o z30.o z31.o z32.o \ z33.o z34.o z35.o z36.o z37.o z38.o z39.o z40.o \ - z41.o z42.o z43.o z44.o z45.o z46.o z47.o z48.o + z41.o z42.o z43.o z44.o z45.o z46.o z47.o z48.o \ + z49.o z50.o z51.o lout: $(OBJS) $(CC) -o lout $(OBJS) $(ZLIB) -lm |